River Flood

Flood a river valley and time when the water reaches each house, with levees, trenches, a bypass channel or a dam break.

  • House
  • House reached
Water depth0.1 m3 m or more
Groundlowhigh
100%

The river enters at the left and leaves at the right. Drag with Raise to build banks and levees, or with Lower to dig trenches, a meter per pass, while the water flows; Rerun starts again with your ground. Point at a house for its arrival time, depth and speed.

Setup
Scene
Ground tool
Model
150 m³/s
0.035
View
1 min per second

How is River Flood working for you?

About River Flood

Model
Shallow-water equations, finite volumes
Grid
15 m cells, 1.44 by 1.08 km
Exact check
Ritter's dam break (1892)
Friction
Manning's n

River Flood follows a river that carries more water than its channel holds as it spreads over a valley floor, seen from above. The water moves by the shallow-water equations, solved on a grid of 15 m cells with finite volumes: the hydrostatic reconstruction of Emmanuel Audusse and colleagues (2004), which keeps still water still over uneven ground, and a Rusanov flux, which never makes a depth negative. Friction follows Manning's formula with the roughness n.

Each house records when water first reaches it, more than 10 cm deep, and how deep and fast the water there becomes. A levee along the river keeps the water in the channel until it overtops; a bypass channel takes part of the flow around the town; a trench or a bank drawn by hand changes where the water goes. The readout gives the flooded area and the houses reached.

The Dam break scene holds a reservoir 4 m deep behind a dam on flat ground. Break the dam and the water runs out across the dry valley; with no friction, the depth along the valley follows the exact solution August Ritter found in 1892, as SWASHES gives it, and the chart draws it beside the computed depth. Compare scenes in the Runs table and export a PNG, video, GIF or CSV.

How to use River Flood

  1. Pick a scene. Choose River valley, Dam break, Levee, Levee overtopped or Bypass channel. Each preset sets the scene, the inflow and the friction.
  2. Set the flow. Inflow sets the river's flow at the left edge, from 10 to 400 m³/s; Manning n sets how rough the ground is, from 0 for no friction to 0.1.
  3. Shape the ground. Pick Raise and drag to build a bank or levee, or Lower to dig a trench; each pass changes the ground by 1 m, and the water flows around it as you build. Rerun starts again from the first second with your ground, Restart clears it, and Reset returns every setting to its default.
  4. Break the dam. In the Dam break scene, press Break the dam to remove it. The chart compares the depth along the valley's middle with Ritter's exact solution when Manning n is 0.
  5. Compare scenes. When every house is reached, or after 6 hours of model time, the run adds a row to the Runs table: houses reached, the first and last arrival, the deepest water at a house and the flooded area.
  6. Export. Save a PNG, record 8 seconds, or record the full run. The CSV files hold the flooded area every 30 s and the Runs table, and a share link carries your ground.

Frequently asked questions

How fast does a flood reach a house?

It depends on how much water leaves the channel, how far the house is and how rough the ground is. In the River valley scene at 150 m³/s, water reaches the first house within about 10 minutes of model time and the town within about half an hour; with the levee the town stays dry for more than three hours.

What does a levee do?

It raises the river's banks, so the channel holds more water before it spills. Once the flow is larger than the channel with its levees can carry, water pours over the top and floods the land behind it. Compare Levee with Levee overtopped.

What is Ritter's solution?

The exact shape of the water after a dam vanishes at once on a flat, dry, frictionless bed, found by August Ritter in 1892: the surface falls along a parabola from the reservoir's depth to zero, the wave front moves at twice √(g·h), and the reservoir drains backward at √(g·h). SWASHES (Delestre and colleagues, 2012) gives the formulas.

Is this a flood map for a real place?

No. The valley, the river, the houses and the friction are model settings, and real flood maps use surveyed ground, rainfall and river records. The model shows how water spreads and what banks, levees and channels change, as depth, speed and arrival time.

References

  1. Audusse, E., Bouchut, F., Bristeau, M.-O., Klein, R., & Perthame, B. (2004). A fast and stable well-balanced scheme with hydrostatic reconstruction for shallow water flows. SIAM Journal on Scientific Computing 25(6), 2050–2065.
  2. Delestre, O., Lucas, C., Ksinant, P.-A., et al. (2012). SWASHES: a compilation of shallow water analytic solutions for hydraulic and environmental studies. International Journal for Numerical Methods in Fluids 72(3), 269–300.
  3. Bates, P. D., Horritt, M. S., & Fewtrell, T. J. (2010). A simple inertial formulation of the shallow water equations for efficient two-dimensional flood inundation modelling. Journal of Hydrology 387, 33–45.