Cloud Formation
Watch clouds form in a slice of sky as warm air rises, cools and condenses, and see what makes cumulus, stratus or a storm.
- Cloud
- Ice
- Rain
- Ground
- Cloud base, lifted surface air
- Freezing level
Warm air rises, cools and makes cloud where its vapor saturates; the dashed white line is where air lifted from the ground would saturate. Tap to warm the air there, an event in time that Rerun and share links leave out.
How is Cloud Formation working for you?
About Cloud Formation
- Section
- 10 km wide, 8 km high, 125 m cells
- Dry adiabatic lapse rate
- 9.8 °C per km (NWS)
- Saturation
- es = 6.11 × 10^(7.5T/(237.3 + T)) hPa (NWS)
- Step
- 5 s
Cloud Formation shows a slice of the sky 10 km wide and 8 km high, seen from the side. The air is a fluid that carries its temperature, water vapor, cloud water and rain; warm air rises because it is lighter, and rising air expands and cools. Air that is not saturated cools at 9.8 °C for every kilometer it rises, the dry adiabatic lapse rate (US National Weather Service), and once its vapor reaches saturation the excess condenses into cloud and releases heat, which keeps the cloud rising.
Saturation follows the National Weather Service's formula for vapor pressure, es = 6.11 × 10^(7.5T/(237.3 + T)) hPa at T °C. The dashed white line is the cloud base for air lifted straight from the ground, computed from that formula: thermals that mix with drier air on the way up form their clouds higher. Above the dashed blue freezing level the cloud is drawn as ice. Cloud water past the rain threshold turns into rain that falls at 5 m/s.
What makes the clouds is the air: humid air near the ground and a steep lapse rate give tall clouds and thunderstorms, a stable, moist layer gives a flat stratus deck, wind over a hill gives a cap cloud, and dry air gives thermals with few clouds, high up and short-lived. Compare skies in the Runs table and export a PNG, video, GIF or CSV.
How to use Cloud Formation
- Pick a sky. Choose Fair-weather cumulus, Stratus, Over a hill, Thunderstorm or Dry day. Each preset sets every control in Model.
- Set the air. Surface temperature and Surface humidity set the air at the ground; Lapse rate sets how fast the still air cools with height above a mixed layer 600 m deep.
- Lift it. Heating warms five patches of ground where thermals start; Hill puts a low or high hill in the wind, and Wind sets its speed. Tap the sky to warm the air there for a moment.
- Watch the clouds. White is cloud water, pale blue cloud above the freezing level is ice, and blue squares are rain. The dashed white line marks where air lifted from the ground would saturate.
- Compare skies. After 60 minutes of model time the run adds a row to the Runs table: cloud base and top, the share of the sky with cloud, and the rain at the ground. Rerun plays the same thermals again; Randomize sets every Model control at random, with new thermals.
- Export. Save a PNG, record 8 seconds, or record the full hour. The CSV files hold the cloud water every minute and the Runs table.
Frequently asked questions
Why do clouds have flat bases?
Because rising air saturates at about the same height: air lifted from the ground cools at 9.8 °C per kilometer (US National Weather Service) until its vapor reaches saturation, and that height, the lifting condensation level, is nearly the same for neighboring thermals. The dashed line in the tool marks it for air lifted straight from the ground.
What makes a thunderstorm instead of a small cumulus?
A steep lapse rate and humid air. When the still air cools faster with height than rising cloud does, the cloud stays warmer and lighter than its surroundings and keeps rising, releasing heat as it condenses. Compare Fair-weather cumulus with Thunderstorm.
Why is the cloud base higher than the dashed line?
Rising thermals mix in drier air from around them, so they need to rise farther before they saturate. The dashed line is for air lifted from the ground with no mixing.
How real is it?
It is a flat slice of the sky without radiation, with simple rain and ice and no lightning. The heating, the mixed layer, the rain threshold and fall speed and the hill are model settings; the dry adiabatic lapse rate and the vapor-pressure formula come from the US National Weather Service.
References
- Stam, J. (1999). Stable fluids. Proceedings of SIGGRAPH 99, 121–128.




